Avid Technology SYNC HD Specifikace Strana 63
- Strana / 107
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Chapter 5: Additional Operational Information 59
Chapter 5: Additional Operational
Information
Front Panel Generator/Parameter Controls
This section details the parameters available from the multi-function Set, Down, Up and
Run/Stop/Clear/Esc switches on the SYNC peripheral front panel. For details on the multi-function
Generator/Parameter switches on the front panel, see “Front Panel Generator/Parameter Switches”
on page 35.
Parameters
SYNC peripheral parameters are selected and edited using the four Generator/Parameter switches.
To select SYNC peripheral front panel parameters:
1 Press Set.
2 Use the Up and Down switches to scroll through available parameters, described below.
The 7-segment LEDs in the Generator/Parameter Display abbreviate some parameter names using nu-
merals to represent letters (such as “5” to represent “S” or “s”). The following table identifies each of
these abbreviations.
- HD Guide 1
- Legal Notices 2
- Documentation Feedback 2
- Contents 3
- SYNC HD Guideiv 4
- Chapter 1: Introduction 5
- SYNC Peripheral Features 6
- System Requirements and 7
- Compatibility 7
- Registration 8
- About This Guide 8
- Conventions Used in This 9
- About www.avid.com 9
- SYNC HD Guide6 10
- Hardware Connections 11
- Clock for Pro Tools 12
- Audio Interfaces 12
- MachineControl 13
- Synchronization and 13
- Timecode Connections to 13
- Machines, Decks, and Other 13
- Connecting LTC 14
- Connecting Word Clock Devices 14
- Connecting AES/EBU Devices 15
- Connecting MIDI Timecode 15
- Software Installation 16
- Emulating a SYNC I/O 17
- Configuring a SYNC 18
- Peripheral from Pro Tools 18
- Clock Source 19
- Clock Reference 19
- SYNC HD Guide16 20
- Speed Cal 21
- SYNC Setup section 21
- Video Ref Format 22
- Video In Format Settings at 23
- HD Video Reference Rates 23
- Configuration 24
- Software Configuration for 24
- Troubleshooting 25
- Synchronization Accuracy 26
- Software 27
- Loop Master Indicator 28
- Sample Rate LEDs 28
- Generator/Parameter Controls 28
- Timecode Display 28
- Parameters and Values 29
- Remote Mode 29
- SYNC Peripheral Back Panel 30
- Host Serial Port 31
- Video In/Out 31
- LTC In/Out 31
- AES/EBU In/Out 31
- SYNC Setup Software Utility 32
- SYNC HD Guide30 34
- Bi-Phase/Tach Parameters 35
- Generator/Bi-Phase Preset 35
- Variable Speed Override (VSO) 35
- Override (VSO)” on page 42 35
- SYNC HD Guide32 36
- From Pro Tools 37
- (Windows Only) 37
- Utility, and the Front Panel 38
- Front Panel 39
- Generator/Parameter 39
- Switches 39
- Clock References and 40
- Video and Clock Reference 41
- Alignment 41
- Clock) Options 42
- LTC and Clock Reference 43
- Pilot Tone 44
- Bi-Phase/Tach and Clock 45
- Reference 45
- Positional Reference 47
- VITC and Positional Reference 48
- Auto LTC/VITC Positional 49
- Serial Timecode 50
- Bi-Phase/Tach 50
- SYNC HD Guide48 52
- Compensating for Timecode 53
- Timecode 53
- Generator Preset Mode 54
- LTC Generation/Regeneration 55
- VITC Generation/Regeneration 56
- Auto LTC/VITC 57
- External 57
- Internal VITC Generation 58
- MTC Generation/Regeneration 59
- Generating a Window Dub 60
- Edit Window 62
- Information 63
- Pull Rate 64
- Set Generator Start Time 64
- Digital Clock Reference 64
- Sample Rate 64
- Window Dub/Burn 66
- Freewheel Length/Duration 66
- LTC Output Level/Gain 66
- 0000 (LTC 0 - fastest) 67
- -0001 (LTC 1) 67
- -0002 (LTC 2 - average) 67
- -0003 (LTC 3) 67
- -0004 (LTC 4 - smoothest) 67
- Bi-Phase/Tach signal: 68
- To select a video system: 68
- HD Video Format 69
- MTC Idle Mute 69
- Device ID 69
- USD Compatibility Mode 69
- Using Fader Start 70
- Calibrating the SYNC 70
- Peripheral Oscillator 70
- Recalibrating 71
- Restoring Factory Settings 72
- Managing and Selecting 73
- Video Inputs 73
- SYNC HD Guide70 74
- LTC Signals 76
- Auto-Switch LTC/VITC 76
- Digital Clock Signal Types 77
- SYNC HD Guide76 80
- SYNC HD Guide78 82
- Rear Panel Connectors 84
- Assignments 89
- Bi-Phase/GPI/Pilot 90
- Bi-phase/Tach 91
- GPI Relay Outputs 92
- GPI (TTL)/MTC Outputs 93
- GPI (opto) Inputs 94
- Connector Pin Assignments 95
- SYNC HD Guide92 96
- SYNC Peripheral Cable Pin 97
- Bi-phase/Tach/GPI/Pilot Port 98
- Interfacing Notes 98
- Environmental Compliance 99
- EMC (Electromagnetic 100
- Compliance) 100
- Safety Compliance 101
- SYNC HD Guide98 102
- Index 99 103
- SYNC HD Guide100 104
- Index 101 105
- SYNC HD Guide102 106
- Technical Support (USA) 107
- Product Information 107
Související produkty a manuály pro Generátory energie Avid Technology SYNC HD
(106 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.029 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce